4000-891-306
 
 
 
 
外形专利设计。十年自主研发生产经验。为您提供适合您的--低成本的--高性能的--可靠的工业遥控系统
LX-100-TB

LX-100-TB工业无线遥控器
1. 技术指标:
1.1. 遥控器:
1.1.1. 按键(遥控器):8键
1.1.2. 调制方式:FSK。
1.1.3. 遥控距离:200米
1.1.4. 供电:2节1.5V AA电池。
1.1.5. 使用环境温度:-20℃~+50℃。
1.1.6. 防水等级:IP65。
1.1.7. 重 量:290 克。
1.1.8. 外型尺寸:215×75×30mm
1.2. 控制器:
1.2.1. 输出继电器:1个主回路电源控制继电器,1个警铃控制继电器,6个功能控制继电器。
1.2.2. 触点负载能力:5A  250VAC,5A  30VDC。
1.2.3. 天线:内置天线,可选择外置天线,定货时选定。
1.2.4. 控制器:交流36V、220V、380 V可选,定货时选定。
1.2.5. 使用环境温度:-20℃~+50℃。
1.2.6. 防水等级:IP65。
1.2.7. 重 量:780 克(不含接线电缆)。
1.2.8. 外型尺寸:60×135×203mm
2. 日常操作:
2.1. 装上磁控开关,按遥控器“电源”键,启动无线遥控系统,遥控器上的指示灯慢速闪亮。
2.2. 根据需要按“上/Up”、“下/Down”、等相应按键进行操作,键按下时,指示灯快速闪亮。
2.3. 按“急停”键后,被控设备主电源断电,系统停止工作,指示灯熄灭。
2.4. 遥控器与控制器的配置:
2.4.1. 新出厂的配套遥控器和控制器已完成配置操作,重新配对使用遥控器和控制器需先进行配置操作,选择新频道,并为控制器设置与遥控器相同的地址。
2.4.2. 打开控制器外壳,给控制器通电。
2.4.3. 取下遥控器的磁性开关,按一下控制器线路板上的设置按钮,这时控制器上的设置指示灯熄灭,然后按下、放开遥控器上的“电源”键三次,再同时按一下“东/East”、“南/South”、“西/West”、“北/North”四个按键,这时,遥控器启动与控制器的配置过程,自动向控制器发送配置信息,发送过程中遥控器的指示灯快速闪亮,待遥控器发送指示灯熄灭后,完成配置过程,若20秒钟内控制器没有收到发射器的配置信号,控制器将自动恢复原有状态。
2.5. 遥控器低电压指示:
电量正常~LED显示绿色,遥控器正常工作
电量极低~LED显示红色,遥控器停止工作,必须更换电池。
3. 注意事项:
3.1. 操作遥控系统前应详细阅读本说明书。
3.2. 使用本无线遥控系统的人员,应取得操控相应设备的资质,确保正常操作设备,以免发生危险。
3.3. 应确保遥控器电池电量充足,当出现电池电压偏低报警时,要尽快更换1.5VAA电池(不可使用1.2V可充电电池)。
3.4. 安装或维修无线遥控系统时,应关闭系统总电源,避免发生触电危险。
3.5. 安装控制器时,应避免控制器被金属部件覆盖,产生屏蔽现象,降低接收灵敏度。
3.6. 未经专业培训人员不得拆开本机,以免造成损害。
3.7. 系统出现故障后,应由专业人员维修,或与代理商联系。

 

 

LX-100-TB industrial wireless remote control

1 technical indicators:

1.1. remote control:

The 1.1.1. button (remote control ) : 8 keys

1.1.2. mode: FSK.

1.1.3.: remote control distance of200 meters

Power supply:1.1.4.2 1.5V AA battery.

1.1.5. use of the environment temperature: -20℃ ~+50 ℃.

Waterproof grade: IP651.1.6.

1.1.7. weight:290 gram.

1.1.8. size:215x 75 x30mm

1.2. controller:

The 1.2.1. output relay:1main loop power control relay,1alarm control relay, a 6 function control relay.

1.2.2. contact load capacity:5A250VAC,5A30VDC.

The 1.2.3. antenna: the built-in antenna, can choose an external antenna, when ordering the selected.

1.2.4. controller:36V,220V, V AC380optional, ordering the selected.

1.2.5. use of the environment temperature: -20℃ ~+50 ℃.

Waterproof grade: IP651.2.6.

1.2.7. weight:780 grams ( excluding wiring cable ).

1.2.8. size:60x 135 x203mm

2daily operation:

2.1. mounted on the switch controlled by a remote controller, according to the" power" button, start the wireless remote control system, remote control on the indicator slow flash.

2.2. according to the need to" /Up"," /Down", and the corresponding key operation, press the button, indicator light flashes rapidly.

2.3. press the " stop" button, the main power supply system of the controlled equipment, stop working, indicator lights.

2.4. remote controller and controller configuration:

2.4.1. new factory matching remote controller and controller has completed the configuration operation, pair using a remote control device and controller need to configure operation, select the new channel, and for the controller is provided with remote control the same address.

2.4.2. open controller shell, to the controller power.

2.4.3. remove the remote control of the magnetic switch, click the settings button controller circuit board, then the controller is set on the light goes out, and then press, let go of remote control on the" power" button three times again at the same time, press the " /East"," /South" south", West / West."," North /North" four keys, the remote start controller, and the configuration process, automatically to the controller sends configuration information, the process of sending remote control indicator light flashes rapidly, the remote controller transmits light is extinguished, completing the configuration process within 20 seconds, if the controller fails to receive configuration of the transmitter signal, the controller will automatically restoring the original state.

2.5. remote controller of low voltage indication:

Electric normal ~ LED display green, remote control work

Very low power levels to LED display red, remote control to stop work, must replace the battery.

3points for attention:

3.1. operating remote control system should read the prospectus.

3.2. use the wireless remote control system of personnel, should be obtained to control corresponding equipment qualification, ensure the normal operation of equipment, in order to avoid danger.

3.3. shall ensure that the remote controller battery is enough, when the battery voltage is low when the alarm as soon as possible, to replace 1.5VAA battery ( not use1.2V rechargeable battery ).

3.4. installation or repair wireless remote control system, should shut down the system power, to avoid the risk of electric shock.

The 3.5. controller is installed, should avoid controller is metal parts are covered, from shielding phenomenon, reduction of receiving sensitivity.

The 3.6. without professional training personnel shall not open the machine, so as not to cause damage to.

3.7. system failure by professionals, repair, or contact with the agent.

版权所有:天津博奥亿美电子科技有限公司 友情链接:光纤熔接机       技术支持:企商科技